
شارژ تونر در پرینتر ها
سلام به همه همراهان همیشگی ، در این مطلب قصد داریم چگونگی شارژ تونر در پرینترها را بیان کنیم ممکن است زمان جایگزینی تونر کارتریج فرا رسیده باشد.شارژ تونر در پرینتر ها کار بسیار راحتی می باشد .
مراحل زیر برای کارتریج پرینتر های سامسونگ مدل های
(ML-1860/ ML-1865/ ML-1865w/ ML-1660/ ML-1667/ ML-1665) و همچنین مدلهای (SCX-3200/ SCX-3205/ SCX-3205w/ SCX-3207)
یکسان میباشد
برای شارژ پودر کارتریج خود طبق مراحل زیر عمل نمایید.
اولین مرحله تهیه وسایل مورد نیاز است که عبارتند از یک شیع نوک تیز مثل چاقو یا کاتر ویک پیچ گوشتی.
توجه داشته باشید اینکار را می بایست در فضای مناسب انجام داد زیرا مقدار پودر باقی مانده در کارتریج را می بایست تخلیه کنید و اینکار سببب پخش شدن این پودر وسیاه شدن مکان اطراف شما خواهد شد.
نکته دیگر اینکه:از پاک کردن گریس های دور چرخ دنده ها ومیله فلزی بپرهیزید .زیرا این گریس از نوع هادی جریان برق است و در نبود آن دستگاه پرینتر شما به درستی کار نخواهد کرد.
کارتریج را از درون پرینتر بیرون بکشید. در سمت راست کارتریج همچین شکلی را مشاهده خواهید کرد.
زائده های پلاستیکی که با دایره قرمز مشخص شده اند را میبایست با یک کاتر برید تا بتوان این قسمت را از کارتریج جدا نمود
پس از جدا کردن این قسمت مانند شکل زیر درپوش مشکی رنگ را به کمک یک پیچ گوشتی از جایش خارج کنید.
کارتریج را برعکس گرفته وسعی کنید با تکان دادن متناوب کارتریج تمام پودر باقی مانده آنرا بیرون بریزیددر این مرحله نوبت به پر کردن محفظه تونر با پودر خریداری شده است.
مانند شکل زیر قوطی پودر را در یک دست و کارتریج را در دست دیگر بگیرید وشروع به پرکردن محفظه تونر نمایید.در زمان ریختن پودر به داخل محفظه با کف دست خود ضربات آرام و پی در پی ای را به بدنه کارتریج بزنید تاعمل پرشدن محفظه تونر به درستی انجام شود.
در نهایت در پوشی را که به کمک کاتر جدا نمودهبودید را به درستی وبا کمی فشار در جای خود محکم کنید.
در حال حاظر کارتریج شما شارژ شده وبا قرار دادن آن در پرینتر میتوانید از آن استفاده نمایید.
شارژ تونر در پرینتر ها
Charging the toner in printers
Hello, All the regular enthusiasts, In this article, we’ll talk about how to charge the toner in printers. It may take time to replace the toner cartridge. The toner discharge is very easy for printers.
The following steps are for Samsung printer cartridges
(ML-1860 / ML-1865 / ML-1865w / ML-1660 / ML-1667 / ML-1665) as well as models (SCX-3200 / SCX-3205 / SCX-3205w / SCX-3207)
Is the same
To charge your cartridge powder, follow the steps below.
The first step is to make the necessary items, which include a sharp tip, such as a knife, a knife and a screwdriver.
Note that this should be done in the appropriate space because the amount of remaining powder in the cartridge should be drained and this will cause the powder to spread around the area around you.
The other thing is: Avoid removing greases around the gears and metal parts. Because this grease is a conductive type of current, and in the absence of this printer, your printer will not work properly.
Remove the cartridge from the printer. You’ll see this shape on the right side of the cartridge.
The plastic appendages marked with the red circle should be cut with a cutter so that it can be removed from the cartridge.
After removing this part, pull out the black cover with the help of a screwdriver, as shown below.
The hollow cylinder you see is the same as your cartridge powder tank.
Take the cartridge in reverse and roll it out by flipping the cartridge all the remaining powder. At this point, it’s time to fill the toner container with powder.
Like the shape below, put a can of powder in one hand and a cartridge in the other hand and begin to fill the toner container. When pouring the powder into the compartment with your palm, push the calf and successively into the cartridge body to fill the toner container To be done correctly.
Finally, firmly tighten the screw that you cut off with the cutter.
Image result for toner in printers
Now your cartridge is charged and you can use it to put it in the printer.
سلام ، گریس هادی جریان برق چه مارکهایی وجود دارد ؟
برای شارژ کارتریج می خواهم .